How To Build An Awning Frame From Wood

If you lot want to give the exterior of your home some added dimension and instant curb appeal, larn how to build a wood canopy over your front end door. This is a challenging chore that requires a few actress hands and the better function of a solar day, but once it'southward complete your home will never have looked better.

Materials and Tools

Pry bar
Ladder
Hammer
Galvanized covering nails
Galvanized framing nails
Carpenter'southward level
Ballast plate or bolt
Felt newspaper
Asphalt roof shingles
Drip border
Circular saw
4x4s
Plywood
2x4s
Concrete mix

Building a Wood Awning Over a Door

Prepping the Firm

The woods canopy should extend at least one foot by both sides of the door and be positioned at least three feet above the door. Remove all of the siding within this surface area using a apartment pry bar. Pry information technology away cleanly because it will be going back in place once the installation is complete.

Building the Frame

Secure a level 2x4 to the side of the business firm by screwing information technology straight into the framing members using lag screws. The 2x4 should be six to twelve inches higher up the door trim and the board should extend 12 to 24 inches beyond both sides of the door. The board should be perfectly centered with both ends equidistant from the door's center.

Accept 2 lengths of 2x4 and cut them to the aforementioned size as the original piece you installed to the business firm. Cutting the ends of both pieces at an angle and place them against the firm and then they class a triangle with the original board. The triangle should exist 1 to two foot loftier at the heart. Secure the two boards to the framing members using lag screws.

Set up a pair of sawhorses and use them to make a second triangle in the same dimensions as the one on the house. Adhere plywood cleats on one side of the triangle to hold it together.

Assembling the Woods Canopy

Decide how far y'all want your wood canopy to stick out over the door and cut three pieces of 2x4 to that length. Almost wood awnings stick out between three and five anxiety.

Smash the iii boards to the side of the triangle with the plywood brace, so raise the entire frame and secure information technology to the triangle on the firm using temporary wooden braces to hold it upwards. Make sure the frame is level and secure everything in place using galvanized nails or decking screws.

Physical Support Piers

Dig 2 holes in the ground, one at each corner of the overhang, no less than two feet deep. Each hole should be equidistant from the house and straight under the end of the awning frame.

Fill the holes with concrete and fix an ballast plate or bolt on summit while the mix is still wet. Make certain the ballast plate or bolt is positioned so that the 4x4 support posts line up with the inside of the awning frame.

Cut the 4x4s to length and attach them to the anchors. Brand sure they are plumb in both directions and attach them to the frame using lag bolts.

Rafters and Fascia

Install one or two rafters on each side of the frame and add 3 pieces of fascia to the frame. For the fascia, use 1x6 fir or pine (without knots). Blast the fascia in place starting a half an inch below the top of the awning'south roof line.

Installing the Roof

Lay the plywood on the roof and then it extends one inch over the sides and the front end. Nail the drip edge in place and apply the felt paper over the plywood.

Install the asphalt shingles starting from the bottom upwards. Cutting pieces of shingle and apply the roof cap.

Installing the Awning's Ceiling

Cut two or three 2x4s, space them evenly apart and blast them to the underside of the canopy. Finish the ceiling with beaded ceiling board or install 1x4 planks to fill in the space.

Finishing the Installation

Paint the awning earlier y'all replace the siding to foreclose drips from getting on the siding. Once the pigment is dry, replace the siding on the house and the job's consummate.